A pocket door frame would be needed in installing a concealed door. This will make a room more versatile because it can be simply closed off from the other parts of the house if needed. This is an excellent way to maximize the space in your living room. With patience and the right information, you can simply accomplish it by yourself. There are some steps that would definitely help you learn the whole process.
You must always know and distinguish if a particular wall that you picked would be perfect for some installation. It must have the size which is twice as the door to accommodate such changes. Also, check for some loads that the wall might be bearing. Checking the arrangement of the wall in your house may help you identify it.
Verify that the wall should not have any electrical wiring or some pipes that is running through it. Search for the switches and electrical outlets to ensure safety. If you have an attic or a certain basement, wiring may be rerouted through it. But, if you find some pipes, you can never put a frame in it.
Replace the current header by using a saw with a metal blade for cutting through the nails in order to remove the jamb. Remove the pieces of the board as well by using a wood blade. Always take caution to keep the cut shallow. Use the section of the drywall that is found above the door in order to frame a new header.
Take away the existing door by pulling it off simply from its moldings. This would usually create a particular gap which could be used to further access the shims. You can use a saw in the bunch of nails which is around the shims. Tip the blade of the saw in a downward motion to have a shallow cut in the drywall and to remove it from the studs.
Leave a visible margin that is about two or three inches away from the ceiling upon removing the drywall from the header. A reciprocating saw is often used to remove such. You can also cut through the studs to form another space for the frame. See to it that you cut the nails that connects the studs to its soleplate.
Determine the height of the header by adding about three and one fourth inches to its length and add the height of the soleplate. This will be needed if the floors are carpeted. If there is no carpet, the brackets can be installed easily into the floor.
The stud must be cut in a peculiar length to have another support for a new header. Measure the opening and put the stud in it while observing a certain distance which is the same to its other side. Nails and screws may be used to place the new header and install it directly to the soleplate in the floor.
Finish the installation of your pocket door frame according to the instructions of the manufacturer. Be sure that when framing, the rough opening is plumb and the header is at level or else, it will not slide smoothly. Use some trim screws in the head of the jamb to make it less noticeable as well. You may also paint it prior to the instructions so as to prevent moisture from causing it to warp.
You must always know and distinguish if a particular wall that you picked would be perfect for some installation. It must have the size which is twice as the door to accommodate such changes. Also, check for some loads that the wall might be bearing. Checking the arrangement of the wall in your house may help you identify it.
Verify that the wall should not have any electrical wiring or some pipes that is running through it. Search for the switches and electrical outlets to ensure safety. If you have an attic or a certain basement, wiring may be rerouted through it. But, if you find some pipes, you can never put a frame in it.
Replace the current header by using a saw with a metal blade for cutting through the nails in order to remove the jamb. Remove the pieces of the board as well by using a wood blade. Always take caution to keep the cut shallow. Use the section of the drywall that is found above the door in order to frame a new header.
Take away the existing door by pulling it off simply from its moldings. This would usually create a particular gap which could be used to further access the shims. You can use a saw in the bunch of nails which is around the shims. Tip the blade of the saw in a downward motion to have a shallow cut in the drywall and to remove it from the studs.
Leave a visible margin that is about two or three inches away from the ceiling upon removing the drywall from the header. A reciprocating saw is often used to remove such. You can also cut through the studs to form another space for the frame. See to it that you cut the nails that connects the studs to its soleplate.
Determine the height of the header by adding about three and one fourth inches to its length and add the height of the soleplate. This will be needed if the floors are carpeted. If there is no carpet, the brackets can be installed easily into the floor.
The stud must be cut in a peculiar length to have another support for a new header. Measure the opening and put the stud in it while observing a certain distance which is the same to its other side. Nails and screws may be used to place the new header and install it directly to the soleplate in the floor.
Finish the installation of your pocket door frame according to the instructions of the manufacturer. Be sure that when framing, the rough opening is plumb and the header is at level or else, it will not slide smoothly. Use some trim screws in the head of the jamb to make it less noticeable as well. You may also paint it prior to the instructions so as to prevent moisture from causing it to warp.
About the Author:
You can visit the website heavydutypocketdoorframes.com for more helpful information about Tips In Installing A Pocket Door Frame
No comments:
Post a Comment