Even though the idea of garden fountains being made from pots is not new, I happened upon a method of building one that I hadn't seen before. I think this fountain would make a wonderful addition to any garden and its so easy to build that anyone can do it. The first thing you need to do is choose the appropriate pots. One will be used as the basin to catch the water coming down. The next is a base and then the largest pot is used for the main fountain. When you are choosing the shape for this pot, keep in mind that the function is just as important as how it looks. A slightly tapered pot that is smooth will be very quiet as the water tends to cling on to the sides of the pot as it falls. Pots having ridges or rings will cause the water to splash into the basin causing more sound.
You start with a large sized terracotta or stone bowl as your garden pot foundation. This will be the basin pot where the overflowing water will fall. Drill a hole out of the bottom center of the bowl if there isn't one already. Now take the cord from your pump and run it through the hole. For larger holes, cover with duct tape and fill with a car body filler. Smaller holes can be filled in with silicon. When that has dried, coat the inside with a water sealant. Now you should be ready to place the basin in your desired location. Although not crucial, try to make the basin as level as possible.
The pump is housed inside the base pot that is turned upside down. The diameter of the base should match the diameter of the main large fountain pot. Cut out three or four notches around the top rim of the pot. Its easier to do this if you soak the pot in water overnight. The purpose of the notches is to let water pass in to the base to the pump.
Take a length of tubing a little longer than the height of the main fountain pot and attach it to the pump. Feed the base pot down through the hole in its bottom and seal the gap between the tubing and the hole with silicon. The whole set up should be your basin with an upside down pot sitting in the middle with a tube sticking out from the pump inside it.
Now things should start taking shape. Take the fountain pot and test fit it down over the tube by placing it on top of the base pot. Don't glue it down yet. If it looks good (with the pipe sticking out past the top of the pot) you can take it back off and run a couple of thick beads of silicon around the top of the base pot. The bead around the outside diameter helps hold the two pots together and the bead on the inside closer to the hole will keep water from running in between the pots.
When it is all dry, test it by filling it with water. Adjust the height of the tubing to get the desired effect of the water bubbling up. Finish it off by filling the bottom basin pot with rocks. Enjoy your beautiful fountain!
You start with a large sized terracotta or stone bowl as your garden pot foundation. This will be the basin pot where the overflowing water will fall. Drill a hole out of the bottom center of the bowl if there isn't one already. Now take the cord from your pump and run it through the hole. For larger holes, cover with duct tape and fill with a car body filler. Smaller holes can be filled in with silicon. When that has dried, coat the inside with a water sealant. Now you should be ready to place the basin in your desired location. Although not crucial, try to make the basin as level as possible.
The pump is housed inside the base pot that is turned upside down. The diameter of the base should match the diameter of the main large fountain pot. Cut out three or four notches around the top rim of the pot. Its easier to do this if you soak the pot in water overnight. The purpose of the notches is to let water pass in to the base to the pump.
Take a length of tubing a little longer than the height of the main fountain pot and attach it to the pump. Feed the base pot down through the hole in its bottom and seal the gap between the tubing and the hole with silicon. The whole set up should be your basin with an upside down pot sitting in the middle with a tube sticking out from the pump inside it.
Now things should start taking shape. Take the fountain pot and test fit it down over the tube by placing it on top of the base pot. Don't glue it down yet. If it looks good (with the pipe sticking out past the top of the pot) you can take it back off and run a couple of thick beads of silicon around the top of the base pot. The bead around the outside diameter helps hold the two pots together and the bead on the inside closer to the hole will keep water from running in between the pots.
When it is all dry, test it by filling it with water. Adjust the height of the tubing to get the desired effect of the water bubbling up. Finish it off by filling the bottom basin pot with rocks. Enjoy your beautiful fountain!
About the Author:
Donald Rickerby has been working in gardens since his early childhood and has always been interested in educating others on garden pot and landscaping techniques. If you'd like to know more about garden pots, visit AllGardenPots.com
No comments:
Post a Comment